beemen39

Sliding Patio Door Repair and Replacement Sliding patio doors make a fantastic addition to any home. They're simple to operate and offer an expansive view. As with all doors in the house, they are prone to wear and tear that needs replacement or repair. Regularly clean and lubricate your sliding patio doors regularly to keep them in good condition. Lubricating them using graphite or silicone spray allows them to glide smoothly, extending their lifespan. Roller Replacement If your sliding patio door isn't rolling easily, you may have to lubricate it. If the rollers are worn or damaged, you will need to replace them. Replacing your patio door's rollers will enable your doors to operate smoothly and lessen the amount of force needed to open or close them. If your patio door is an older model, it may be necessary to take off the bottom of the frame in order to access the rollers. If this is the case, use a rubber mallet and a block of wood to loosen the frame and then take it off. Make sure you save the roller screws to use when reinstalling your new rollers. Sliding glass door are a significant security feature in many homes and must be properly protected. repairmywindowsanddoors worn or damaged rollers can make your door hard to push open or closed and can create gaps around the door that intruders can exploit. Replacing your patio door's rollers will ensure that your home is safe from unwanted visitors. After you have removed the top and bottom rails, it is recommended to clean the entire area of the track using an alcohol-soaked cloth. This will remove any dirt and make the task of removing the doors from the tracks much easier. The drainage holes on the bottom track should be visible, but they are often clogged by dirt. If your track seems to be prone to accumulating a lot of dirt, you might want to consider installing an stainless steel u-shaped piece that snaps over the track and provides an extra channel for water to flow through. They are available from CR Laurence, as well as other retailers that specialize in sliding door parts. When you are reinstalling the doors, remember to put the bottom panel into first, and then move the top into the place. You should be able test the doors after they have returned to their original position to make sure they are smooth and don't require a lot of force to open or shut. If the doors feel rough, you can adjust the rollers to give more clearance. Weather Stripping Replacement The weather strip on your sliding door's seals slowly wear away and allow in drafts and moisture, which can increase your energy costs. It is a quick and simple task that can save you money on heating costs. Sliding door weather stripping is available in a assortment of materials, each having its own pros and cons. You'll need to select one that is able to withstand friction, temperature changes, weather changes and foot traffic, while not interfering in the sliding door's operation. Foam and felt are inexpensive however they are susceptible to weather and visible in the frame. Vinyl is more expensive, however it lasts for years. Metals are strong however they might not be appropriate for a modern home. Rubber or plastic can erode with time and require regular replacement. To install new weather strips, take the door from the casing. Find the headstop at the top of the door typically a small piece of metal or plastic that is held in place with screws. Remove the screw caps and then use a screwdriver that is flat to remove the headstop from the bottom of the door. Remove the weather stripping and any residue left behind by using a putty knife or scraper. Don't try to pull the door off its track using just one person. You'll need to use plenty of force. Instead, you should have a second person to hold the door steady as you take it out of its frame. Find the channels that hold your weather stripping. Plugs that match the color of your doors should be put in these channels. Take the plugs off, then pull up on the weather stripping to separate it from its channel. Fin Seal is the most suitable type of weather stripping that is suitable for sliding patio doors. This kind of weather seal has a Mylar that is centered within the brush material and is very durable. It is suitable for almost all climates, and can endure the pressure of walking. The back of the weather stripping is also constructed of a strong, flexible material to better withstand the pressures of a sliding patio door. Door Alignment Patio doors that slide open are a wonderful feature of any home, but as with anything else, they can benefit from an occasional adjustment to make sure they are working at their best. As time passes, sliding patio doors may be worn out or misaligned. This can cause issues such as sticking, bumping against frames, or not locking properly. Regular maintenance and minor adjustments will prevent these problems, saving you both time and money. One of the most common reasons for sliding door misalignment is the damage to tracks or rollers from unexpected jolts, or excessive force. A quick repair using the right tools can fix this issue, ensuring your patio door moving smoothly for years to come. The misalignment could be caused by fluctuations in humidity and temperature or weatherstripping wear, as well as inadequate installation. The latter can result in parts moving and loosening over time which causes the door to move but not close or latch correctly. Over time, these movements can cause air drafts and even let water get into the house. It is important to clean and lubricate your sliding patio door track on a regular basis in order to prevent these issues. A small amount of spray lubricant could easily be purchased at any hardware store and application often with a small amount of brush can keep the track running smoothly. Another common cause of sliding patio door misalignment is that the latch hook is not syncing with the strike plate that is on the jamb. To fix this issue start by opening the door to expose the latch mechanism, and give you complete access to it. Then, locate the adjustment screw that controls the latch hook, and gently rotate it in either direction to adjust its length. A properly adjusted latch will ensure that it will engage and hit the strike plate without resistance or hindrance. Test your door after you have made the necessary adjustments to ensure it locks and slides correctly. Repeat the process if there are problems that persist until your sliding patio doors is fully functional. By following these easy steps, you can save yourself lots of money by not requiring professionals to perform expensive repairs. Frame Replacement Over time, screws on sliding door frames can loosen and allow the frame to move a bit. By regularly tightening and checking these screws, you will be able to prevent your doors from getting stuck or jammed. A sagging screen is fixable with a bit of clamping. However hinges that are loose could need to be replaced. It is possible to repair the patio's sliding feature without having to replace the frame, however, you must first evaluate the condition of the existing frame. This is a cheaper option than replacing the entire frame. It also can meet specific requirements, such as improved insulation. A full frame replacement is the complete removal of the current hinged doors, windows and frame from the wall opening. This allows an entirely new sliding patio be built, and it can offer more flexibility in terms, size and materials. Sliding glass doors are designed to provide you with a stunning view of your backyard, however over time they can begin to show signs of wear and tear. If your sliding glass doors are difficult to open or get stuck it may be necessary to replace the track or wheels. If the frame is in good shape it might suffice to replace the doors. Before you begin, ensure that your work space is free of obstructions. You've laid down a drop cloth. Then, lay the sliding door flat on a work surface and take off the removable grilles or shades. Then make use of a screwdriver remove the plugs that cover the roller adjustment screws at the bottom of the sliding door frame (they're usually covered with caps). Once these are removed, you can loosen and remove the bottom of the door from the track. Once the frame is exposed it is possible to replace the track and sliding door wheels. If your track for sliding doors is damaged or worn out it is best to replace it completely rather than repairing an existing one. You can buy a kit for a DIY project or have an expert do it for you. In either case, follow the instructions provided by the manufacturer to ensure the proper installation.